[email protected]

ARTICLE Effect of rolling reductions on microstructure

The 2Cr13/316L multilayered composite plates were fabricated by hot rolling with recycle heating step. The effect of rolling reductions on microstructure and properties was investigated. The 2Cr13 layer consists of martensite and lath ferrite, but the middle layer has less ferrite than both sides. Effect of Finish Rolling Temperature on the The reheating temperature, rolling conditions (temperature and reduction), cooling rate and cooling interrupt temperature constitute the main adjustable TMCP parameters. Much research has been executed to investigate the effects of rolling conditions on the microstructure evolution and resultant mechanical properties of high-grade microalloyed pipeline

Effect of Finishing Rolling Temperature on Microstructure

Effect of Finishing Rolling Temperature on Microstructure and Mechanical Properties of Microalloyed TRIP Steels October 2013 Journal of Iron and Steel Research International 20(10):7580 Effect of Rolling Temperature on the Microstructure and Metals (2018-11-01) . Effect of Rolling Temperature on the Microstructure and Mechanical Properties of Mg-2Zn-0.4Y Alloy Subjected to Large Strain Rolling Effect of Rolling Temperature on the Microstructure and The 47Zr-45Ti-5Al-3V (wt.%) alloy was solution-treated at 850 and 780 °C for 30 min and then rolled at different temperatures. The effect of rolling temperature on microstructure and tensile properties was investigated. The results showed that the microstructure contained a large amount of phase at a rolling temperature of 600 °C. As the rolling temperature increased, the amount of

Effect of Rolling and Heat Treatment Process Tempering on

Apr 15, 2021 · The effects of rolling process and tempering temperature on microstructure and mechanical performance of experimental steel are studied. The results show that the yield ratio and elongation of the Effect of homogenization and hot rolling on the mechanical Dec 15, 2019 · @article{osti_1614991, title = {Effect of homogenization and hot rolling on the mechanical properties, microstructure and corrosion behavior of U-10Mo monolithic fuel}, author = {Prabhakaran, Ramprashad and Gardner, Levi and Joshi, Vineet V. and Burkes, Douglas and Lavender, Curt A.}, abstractNote = {Corrosion behavior is an important consideration in the fuel qualification Effect of rolling temperature on the microstructure and Jul 23, 2018 · The results showed that rolling at temperatures between 25 and 60 °C could slightly influence the crystal forms of the -PVDF films, but induce a well-oriented -phase structure. Moreover, rolling at temperatures below 60 °C can significantly reduce the crystallite size of PVDF.

Effect of the pouring temperature by novel synchronous

In the process, the pouring temperature has great effects on the microstructure and mechanical property primarily through the crystal change in the rolling-casting area. Temperature of liquids and solids of ZL104 alloy is measured by differential scanning calorimetry. Effects of cold rolling and subsequent annealing on the Effects of cold rolling and subsequent annealing on the microstructure of a HfNbTaTiZr high-entropy alloy Volume 31, Issue 24 Wenqian Wu (a1) , Song Ni (a1) , Yong Liu (a1) and Min Song (a1) Effects of rolling temperature on microstructure, texture Fe-6.5 wt% Si non-oriented electrical steel sheets with a thickness of 0.50 mm were produced by using a new processing route:strip casting followed by hot rolling, intermediate temperature (150-850 °C) rolling and final annealing. The present study focused on exploring the effects of rolling temperature varying from 150 to 850 °C on the microstructure and texture evolution, the formability

Effects of the rolling temperature on microstructure and

Abstract The microstructure and mechanical properties of 2Cr13/316L composite plates by hot-rolling at different rolling temperatures of 1130 °C, 1180 °C, 1250 °C, 1300 °C are investigated in details. With the increase of the rolling temperature, the tensile strength and bending strength of 2Cr13/316Lwere reduced first and then increased slightly due to the coarsening of grains and the The Effect of Rolling Temperature on the Microstructure The Effect of Rolling Temperature on the Microstructure and Mechanical Properties of 5 vol.% (TiBw + TiCp)/Ti Composites January 2020 JOM:the journal of the Minerals, Metals & Materials Society 72(3) The effect of finish rolling temperature and tempering on May 01, 2018 · The paper presents the effect of finishing rolling temperature (FRT) relative to the non-recrystallization temperature (T NR) and the effect of long time tempering on the microstructure, dislocation density and mechanical properties of direct-quenched coiled strips.

Effect of rolling temperature on microstructure and

Sep 23, 2020 · As the rolling temperature is increased to 950 °C, the intensity of the TiC peaks also increases, and some new phases such as FeTi and -Ti are evolved. This is attributed to the increased rolling temperature promoting atomic diffusion at the Ti/steel interface. Further, Fe atoms penetrate the interior of Ti grains to stabilize the -Ti phase.